MATERIAL SAFETY DATA SHEET
CPEN-8000
Revision Date: 03/01/03
Supersedes: new
Click Here To Download in MS Word Format

1. PRODUCT NAME AND COMPANY IDENTIFICATION

Product Name: CPEN-8000, Chemical Name: Not applicable, mixture, Chemical Family: Mixture,
Formula: Not Applicable, Mixture, CAS Registry Number: Not Applicable, Mixture.

Manufacturer: United Supply Service, Inc., 1550 South Indiana Ave., Suite 300, Chicago, IL 60605

Telephone Numbers: Product Information: (866) 489-9831

2. COMPOSITION/INFORMATION ON INGREDIENTS

* By OSHA definition, 29 CFR 1910.1200 (See Section 3 for Hazard Identification and Section 8 for
Exposure Guidelines)

3. HAZARDS IDENTIFICATION

EMERGENCY OVERVIEW: Irritant. Harmful if swallowed.

Routes of Exposure: Contact, ingestion. Target Organ Effects: Eyes: Dust, mist and solutions may irritate or burn. Skin: Dust, mist and solutions will irritate. Ingestion: May irritate gastrointestinal tract. Inhalation: May irritate nose, throat and chest. Carcinogenicity: Not a carcinogen

4. FIRST AID MEASURES

Eyes: Flush with clean cool water for 15 minutes holding eyelids open. Get medical attention. Skin: Promptly wash skin with plenty of soap and water. Ingestion: Drink plenty of water or milk. Do not induce vomiting. See a physician. Inhalation: Remove to fresh air. If symptoms persist see a physician.

5. FIRE FIGHTING MEASURES

Flammable Properties: Combustible. Auto-Ignition Temperature: 800 degrees C. Hazardous Combustion Products: On decomposition by extreme heat, oxides of carbon and nitrogen. Extinguishing Media: Appropriate to primary fire source. Fire Fighting Instructions: Normal firefighting procedures apply. Self-contained breathing apparatus should be worn. Use water spray to keep containers cool. Other Information: Flash Points: Not Available, Autoignition Temperature: Not Available, Flammability Limits in Air (% by volume): Not Available.

6. ACCIDENTAL RELEASE (SPILL MEASURES)

Confine large spills. Collect spilled material into an appropriate container. Residue may be cleaned up with water but rinse water should not be allowed to enter natural waterways. Spray residue of small spills with plenty of water but do not allow this water to enter natural waterways.

7. HANDLING AND STORAGE

Handling: Avoid contact with eyes and skin. Avoid breathing mist from solutions. Use with adequate ventilation. Storage: When not in use keep container closed. Store in a cool dry location.

8. EXPOSURE CONTROLS/PERSONAL PROTECTION

Engineering Controls: Good general ventilation. Eye Protection: Chemical goggles. Skin Protection: Neoprene or natural rubber gloves, Respiratory Protection: Use only NIOSH/MSHA approved respiratory protection for mists if these might be generated. Other Protective Equipment: As required to minimize skin contact. Eye wash, safety shower, Exposure Guidelines:

9. PHYSICAL AND CHEMICAL PROPERTIES (Typical)

Appearance and Odor: White amorphous solid, characteristic odor. Bulk Density: Approx. 9 lbs/gal. Solubility in H20: Complete, dissolves slowly. pH (1% solution): 7 to 8

10. STABILITY AND REACTIVITY

Chemical Stability: Stable, Conditions to Avoid: Contact with strong acids, oxidizers. Hazardous Decomposition Products: At extreme temperatures, oxides of carbon and nitrogen. Hazardous Polymerization: Will not occur.

11. TOXICOLOGICAL INFORMATION

Toxicology of this product has not been established. Expected to be low to moderate based on components.

12. ECOLOGICAL INFORMATION

This product may cause damage to plant and aquatic life.

13. DISPOSAL CONSIDERATIONS

Dispose of in an approved waste container. Disposer must comply with local state and federal regulations with respect to disposal or discharge.

14. TRANSPORT INFORMATION

DOT Description: Not regulated.

15. REGULATORY INFORMATION

All components are listed on the TSCA Inventory.

16. OTHER INFORMATION

Hazard Ratings: HMIS: Health - 2, Flammability - 1, Reactivity - 0, Protective Equipment: C. NFPA: Health - 2, Flammability - 1, Reactivity - 0.

The above information is based on data available to us and is believed to be correct. However no warranty, merchantability, fitness for any use or any other warranty is expressed or to be implied regarding the accuracy of these data, the result to be obtained from the use thereof, the hazards connected with the use of the material, or that any such use will not infringe any patent. Since the information contained herein may be applied under conditions beyond our control and with which we may be unfamiliar, we do not assume any responsibility resulting from its use. This information is furnished upon the condition that the person receiving it shall make his own determination for the suitability of the material for his particular purpose.